Gas Cutting Equipment - General Stores, Hardware and Tools
Marine gas cutting equipment comprises oxy-fuel cutting torches, regulators, hoses, flashback arrestors, nozzles, and accessories used for cutting and heating steel during ship repair, maintenance, fabrication, and shipbuilding. Systems commonly use oxygen with acetylene, propane, or other fuel gases.
ProShipWorks provides end-to-end support to source and supply Gas Cutting Equipment for marine vessels, ship operators, industrial facilities, maintenance teams and procurement departments.
Last updated:
Product Information
| Product Name | Gas Cutting Equipment |
|---|---|
| Product Category | General Stores, Hardware and Tools |
| Product Reference | 248 |
| Brands / Manufacturers | ESAB, Victor Technologies, Harris Products Group, GCE, Koike |
| Unit of Measure | Set or Piece |
Key Features
| Key Feature |
|---|
| 1. Oxy-fuel cutting of carbon steel and marine structural plates |
| 2. Separate oxygen and fuel-gas pressure regulation |
| 3. Interchangeable cutting tips and nozzles |
| 4. Flashback arrestors and non-return valves for gas safety |
| 5. Suitable for shipyard, onboard repair, and hot-work operations |
Applications of Gas Cutting Equipment
| Application |
|---|
| 1. Ship structural steel cutting and renewal work |
| 2. Removal of brackets, pipes, foundations, and damaged sections |
| 3. Shipyard fabrication, maintenance, and hot-work repair |
Models & Manufacturers
| Model | Manufacturer |
|---|---|
| Journeyman 450 Series Cutting Torch | Victor Technologies |
| 62-3 Cutting Torch | Harris Products Group |
| X11 Cutting and Welding Torch System | GCE |
| 112 Cutting Torch | Koike |
Technical Specifications
| Model | Specification | Value | Unit |
|---|---|---|---|
| Journeyman 450 Series | Fuel gas compatibility | Acetylene and fuel gases subject to torch and tip selection | — |
| 62-3 | Torch type | Oxy-fuel hand cutting torch | — |
| X11 | System components | Cutting torch, welding attachments, regulators, hoses, and accessories | — |
| 112 | Application | Manual oxy-fuel cutting of steel | — |
| General equipment | Typical fuel gases | Acetylene, propane, or propylene according to equipment configuration | — |
Standards, Certifications & Class Approval
Review the available standards and approval information relevant to the product. Actual certification, material traceability, inspection and classification requirements depend on the product type, intended application and purchasing specification.
| Applicable Standards & Certification | Applicable standards may include ISO 5172 for hand-operated gas welding and cutting blowpipes, ISO 2503 for gas regulators, ISO 3821 for rubber hoses, and ISO 7289 for quick-action couplings. Actual compliance depends on the specific equipment and manufacturer. |
|---|---|
| Class Approval | Gas cutting equipment is not normally a class-approved machinery item. Use onboard or shipyard equipment accepted by the vessel's safety management system, flag requirements, hot-work procedures, and applicable classification or statutory requirements. DNV, ABS, Lloyd's Register, BV, and ClassNK may review hot-work arrangements rather than approve generic tools. |
Installation, Maintenance & Safety Information
| Installation Notes | Verify gas type, hose connections, regulator compatibility, and nozzle selection before assembly. Fit oxygen and fuel-gas flashback arrestors or non-return valves where required. Leak-test all connections with approved leak-detection solution; never use oil or grease on oxygen fittings. |
|---|---|
| Maintenance Tips | Inspect hoses, regulators, torch bodies, tips, valves, and arrestors before each use. Clean tips with the correct tip cleaner, replace damaged hoses and seals, and periodically test regulators and safety devices. Store equipment clean, dry, capped, and protected from heat and contamination. |
| Safety Notes | Use only by trained personnel under an approved hot-work permit. Keep cylinders upright and secured, separate oxygen from fuel gas, and provide ventilation and fire watch. Wear flame-resistant clothing, gloves, eye protection with the correct shade, and safety footwear. Check for combustible materials and confined-space hazards before cutting. |
Request a Quote for Gas Cutting Equipment
Contact ProShipWorks for marine or industrial product sourcing, quotations and delivery.
- Vessel name and IMO number
- ETA / vessel schedule
- Berth or vessel location
- Required quantity
- Preferred delivery window
- Shipping agent contact details
Other General Stores, Hardware and Tools Products
Explore our range of marine and industrial General Stores, Hardware and Tools products available for sourcing and supply through ProShipWorks.
Why ProShipWorks?
Trusted & Professional Service
Experienced maritime professionals focused on quality, safety and dependable service execution.
24/7 Rapid Response
Fast response for planned and urgent vessel requirements, whenever support is needed.
Unbeatable Prices
Cost-effective marine services with competitive and transparent pricing for vessel requirements.
Port & Anchorage Coverage
Reliable marine service support across ports, anchorages and offshore locations.